rajivagar
Posts: 9
Joined: Wed Jan 06, 2016 1:42 pm
Location: India

Concox GT06N; require USB Cable, PC Software

Thu Jan 07, 2016 8:27 pm

I have recently purchased a Concox GT06N and would like to explore it further by connecting it to my PC.

Checking the Concox website bore no results.

I would like the following info

1. Which USB cable is required to connect the device to the PC. ( I am guessing it would be a USB -> TTL converter cable )

2. I require the PC software to configure the device.

3. Is the device actively supported by Concox by way of new firmware releases? If yes, where are the firmwares hosted?

I would be very glad if someone helped me with these.

P.S. - I had dropped a mail at their contact id yesterday, yet to hear from them. I have also messaged at their FB page a few minutes back; hoping that they would reply.

HnB06
Posts: 1
Joined: Fri Jan 15, 2016 12:56 am
Location: Mexico
Contact: Website

RE: Concox GT06N; require USB Cable, PC Software

Fri Jan 15, 2016 1:04 am

We have used those models for the last 6 months, and i can tell you the following:

There SEEMS to be a software, but you wont get any answer from concox or find it anywhere on the net ( we didn't anyway).

The cable is a simple USB-to rs232 converter and you can use putty to talk to the device...it seems to respond to AT commands, similar to skypatrol but i havent found any document that describes its commands.

We have talked to a couple of suppliers and none know anything about the software (even though they will happily sell you the usb cable) SO it seems sms is the only way you can program those.

rajivagar
Posts: 9
Joined: Wed Jan 06, 2016 1:42 pm
Location: India

RE: Concox GT06N; require USB Cable, PC Software

Sun Jan 17, 2016 7:50 pm

Was on a vacation and had cut myself off of all modern trappings.

@HnB06 , thank you for your reply. Seems we are pretty much in the same boat.

Well there is some good news.

The email/contact form on Concox site was a fail.

They have a Facebook page though, and it did the trick.

The good guys have replied on their Facebook page; have requested for my email/skype id. Given them that, keeping my fingers crossed.

As an addendum, it seems there are a couple of suppliers here in India who are a direct seller of Concox products, while providing the tracking support on their own customized platforms. I believe they wouldn't be configuring all their units using SMS, neither through AT commands.

There needs to be some UI to do all the config. I am thinking of calling them up tomorrow and pester them.

Shall keep this thread updated if I make any progress.

rajivagar
Posts: 9
Joined: Wed Jan 06, 2016 1:42 pm
Location: India

RE: Concox GT06N; require USB Cable, PC Software

Tue Jan 19, 2016 7:10 am

Finally, managed to get through to the Concox guys through their FB page.

Pretty impressed with the way they helped me out.

1. Have managed to get the PC software to configure GT06N over USB-Serial cable.

2. Firmware version according to them is 'proprietary' [?][?] and I was asked as to why I need it. ( I guess they confused it for firmware sourcecode, the English/Chinese language gap is much more than I had imagined.

Image

I have uploaded the software on the following filesharing sites.

http://www99.zippyshare.com/v/Q6Zw0HuL/file.html

https://www.sendspace.com/file/36fdgk

http://www.4shared.com/rar/7arw3Qhuce/G ... _2014.html

http://ul.to/fwqd2l20

http://uploaded.net/file/fwqd2l20

https://www.mediafire.com/?g9ozqruw3x8bw1n



Getting the file across the GFW of China was a little difficult then I had imagined Apparently, they are more used to sending 'executables' as simple file attachments, which my Gmail was scrapping. Seems access to Dropbox, Google Drive are blocked in China and hence the occasional Internet user in China are more accustomed to sending files as attachments.

Looked around, and found the Mail accounts provided by QQ.COM allow executables as attachment [:D]; it did the trick.

GPS2014
Posts: 86
Joined: Fri Jul 25, 2014 6:18 pm

RE: Concox GT06N; require USB Cable, PC Software

Tue Apr 05, 2016 1:19 pm

Hello rajivagar

I have downloaded the file and have the correct cable and driver, but when i open the program there is no com ports available. Did you have the same problem?

rajivagar
Posts: 9
Joined: Wed Jan 06, 2016 1:42 pm
Location: India

RE: Concox GT06N; require USB Cable, PC Software

Wed May 04, 2016 7:26 pm

HI GPS2014,

I am sorry that I didn't update this thread earlier.

I am facing the same issue.

I used a PL2303 based USB to RS232 converter and this software. But, the program failed to display any COM ports. I am attaching the USB to RS232 converter that I used.

Which data cable did you use? Any generic USB to RS232 converter or some cable specially provided with your device by the Concox guys.

Image

GPS2014
Posts: 86
Joined: Fri Jul 25, 2014 6:18 pm

RE: Concox GT06N; require USB Cable, PC Software

Thu May 05, 2016 2:00 pm

HI rajivagar

I am using the cable i got from Concox
I got it to work with SSCOM3.2
I use AT commands for example AT^GT_CM=gmt,e,0,0

rajivagar
Posts: 9
Joined: Wed Jan 06, 2016 1:42 pm
Location: India

RE: Concox GT06N; require USB Cable, PC Software

Thu May 12, 2016 8:32 pm

Hi GPS2014,

Do you mean you could configure GT06N using the Concox cable and sscom3.2?

beryindo
Posts: 5
Joined: Sat Dec 19, 2015 7:05 am
Location: Indonesia

RE: Concox GT06N; require USB Cable, PC Software

Sun May 29, 2016 7:51 am

god job
Last edited by beryindo on Thu Aug 31, 2017 5:35 pm, edited 1 time in total.

Trackingmantra
Posts: 3
Joined: Mon May 30, 2016 7:52 pm
Location: India
Contact: Website

RE: Concox GT06N; require USB Cable, PC Software

Wed Jun 01, 2016 8:15 pm

can anybody help me to reset gt06n..

i am unable to communicate with device
on every command its showing password error!

Tracking Mantra

beryindo
Posts: 5
Joined: Sat Dec 19, 2015 7:05 am
Location: Indonesia

RE: Concox GT06N; require USB Cable, PC Software

Wed Jun 01, 2016 10:33 pm

Originally posted by Trackingmantra

can anybody help me to reset gt06n..

i am unable to communicate with device
on every command its showing password error!

Tracking Mantra

try
RECOVER,111111

Trackingmantra
Posts: 3
Joined: Mon May 30, 2016 7:52 pm
Location: India
Contact: Website

RE: Concox GT06N; require USB Cable, PC Software

Thu Jun 02, 2016 10:17 am

Hi beryindo....

Thanks i tried this command its also not working... again i am getting password error !!

Tracking Mantra

beryindo
Posts: 5
Joined: Sat Dec 19, 2015 7:05 am
Location: Indonesia

RE: Concox GT06N; require USB Cable, PC Software

Fri Jun 03, 2016 10:09 am

Originally posted by Trackingmantra

Hi beryindo....

Thanks i tried this command its also not working... again i am getting password error !!

Tracking Mantra


hmmm you need reload firmware, but I don't have firmware gt06n, u can request from concox

KhunGolf
Posts: 1
Joined: Thu Jul 28, 2016 8:52 pm
Location: Thailand

RE: Concox GT06N; require USB Cable, PC Software

Thu Jul 28, 2016 9:17 pm

Sir .
I have GT06n from China but I can't set apn.
I try APN,internet# .
But when checked GPRSSET# still APN,,, .
Can anyone help me?

roadpointlimited
Posts: 2
Joined: Mon Dec 04, 2017 12:44 pm

Re: RE: Concox GT06N; require USB Cable, PC Software

Mon Dec 04, 2017 1:01 pm

Hello rajivagar

I have downloaded the file and have the correct cable and driver, but when i open the program there is no com ports available. Did you have the same problem?
Install ABD Drivers first and use 2.35 MM wire i meant USB cable :)

for more details go to - Roadpoint Limited and know more details

Return to “GPS trackers, AVL hardware, SIM subscriptions etc.”